ccna-exam-modules.blogspot.com

cisco-tutorials.blogspot.com

CISCO TUTORIALS: 3.1 CCNA 4 - Voucher Exam

http://cisco-tutorials.blogspot.com/2009/09/31-ccna-4-voucher-exam.html

40 CCNA EXAM MODULES. 31 CCNA 4 - Voucher Exam. Which automatic process is started first whenever power. Is applied to a Cisco router? Empties contents of NVRAM. Looks for the configuration file. Starts the operating system. Which of the following commands sets a condition to allow. Packets through a named ACL? Which of the following authentication processes provides. Protection against playback attacks? Which command displays the active configuration of a router? Sum of the costs based on bandwidth.

cisco-tutorials.blogspot.com

CISCO TUTORIALS: 3.1 CCNA 1 - Final Exam 2

http://cisco-tutorials.blogspot.com/2009/09/31-ccna-1-final-exam.html

40 CCNA EXAM MODULES. 31 CCNA 1 - Final Exam 2. A router determines the path to deliver a packet. What layer of the OSI model does this fact represent? Refer to the exhibit. A network administrator has configured a. Network after subnetting the network number 192.168.0.0/28. Workstation 1 is not able to communicate with Workstation 2. What is the cause of this loss in communications? Workstation 1 and Workstation 2 are on the same subnet. The serial connections are using addresses from the LAN subnets.

cisco-tutorials.blogspot.com

CISCO TUTORIALS: 3.1 CCNA 1 - Module 10

http://cisco-tutorials.blogspot.com/2009/09/31-ccna-1-module-10.html

40 CCNA EXAM MODULES. 31 CCNA 1 - Module 10. How does a router decide where the contents of a received frame should be forwarded? By matching destination IP addresses with networks in the routing table. By matching the destination IP address with IP addresses listed in the ARP table. By matching the destination MAC address with MAC addresses listed in the CAM table. By forwarding the frame to all interfaces except the interface on which the frame was received. Subnetwork has 14 usable host IP addresses.

cisco-tutorials.blogspot.com

CISCO TUTORIALS: 3.1 CCNA 1 - Module 7

http://cisco-tutorials.blogspot.com/2009/09/31-ccna-1-module-7.html

40 CCNA EXAM MODULES. 31 CCNA 1 - Module 7. How does 1000BASE-T use the UTP wire pairs to accomplish. Two pairs are used to transmit and two pairs are used to receive. One pair is used to transmit, one pair is used to receive, one pair. Is used for clocking, and one pair is used for error correction. All four pairs are used in parallel by both hosts to transmit and receive simultaneously. Two pairs of wires are used as in 10BASE-T and 100BASE-TX. Which RJ-45 pins are used to transmit and receive data in.

cisco-tutorials.blogspot.com

CISCO TUTORIALS: 3.1 CCNA 1 - Module 8

http://cisco-tutorials.blogspot.com/2009/09/31-ccna-1-module-8.html

40 CCNA EXAM MODULES. 31 CCNA 1 - Module 8. A network administrator has a multi-floor LAN to monitor and. Maintain. Through careful monitoring, the administrator has. Noticed a large amount of broadcast traffic slowing the network. Which device would you use to best solve this problem? What is the function of a Layer 2 switch? Forwards data based on logical addressing. Duplicates the electrical signal of each frame to every port. Learns the port assigned to a host by examining the destination. Segments 3...

cisco-tutorials.blogspot.com

CISCO TUTORIALS: 3.1 CCNA 1 - Module 3

http://cisco-tutorials.blogspot.com/2009/09/31-ccna-1-module-3.html

40 CCNA EXAM MODULES. 31 CCNA 1 - Module 3. What factors should be considered when selecting. The appropriate cable for connecting a PC to a network? Type of system bus. Distance of cable run. What are two advantages of using UTP cable in a networking. Is stiffer than STP. Is less expensive than fiber. Is easier to install than coaxial. Provides longer distances than coaxial provides. Is less susceptible to outside noise sources than fiber is. What must be changed on every host on the network? Decimal en...

cisco-tutorials.blogspot.com

CISCO TUTORIALS: 3.1 CCNA 2 - Module 1

http://cisco-tutorials.blogspot.com/2009/09/31-ccna-2-module-1.html

40 CCNA EXAM MODULES. 31 CCNA 2 - Module 1. Which of the following devices are used in the. Construction of a WAN? Which basic components do a router and a standard. Desktop PC have in common? Which router component holds the configuration file. When power is lost? Volatile random access memory. Non-volatile random access memory. Which of the following descriptions are true regarding. The management connections on a Cisco router? They are non-network connections. They are synchronous serial ports. Establ...

cisco-tutorials.blogspot.com

CISCO TUTORIALS: 3.1 CCNA 1 - Module 5

http://cisco-tutorials.blogspot.com/2009/09/31-ccna-1-module-5.html

40 CCNA EXAM MODULES. 31 CCNA 1 - Module 5. Which of the following are benefits of peer-to-peer. No centralized equipment required. Centralized administrator not required. Centralized control of assets. What is the most common type of cabling used in LANs? Which items in the exhibit are DTE devices? Which statement is accurate about a WAN link? The link transmits data serially. The link uses a maximum distance of 100 meters. The link uses the same transmission rate as all other. The hosts and this device?

allebookstutorials.blogspot.com

ALL EBOOKs/TUTORIALs: Taste of Korea: Korean Cuisine Full of Wisdom

http://allebookstutorials.blogspot.com/2011/02/taste-of-korea-korean-cuisine-full-of.html

Taste of Korea: Korean Cuisine Full of Wisdom. Young Jin Song is an eminent and inventive restaurateur who has founded several Korean restaurants across Asia. With an exceptional appreciation of Korean food and a comprehensive knowledge of restaurants worldwide he brings a stimulating modern approach to classic Korean dining. He lives in London and travels to Asia on a regular basis. Korean Cooking is his first book. Labels: Taste of Korea. Subscribe to: Post Comments (Atom). 100 Best British Boobs.