DEALERSELECTRIC.COM

biankablog.blogspot.com

THE BIANKA LOG BLOG: Going electric: Part 1: The why and how

http://biankablog.blogspot.com/2008/05/going-electric.html

THE BIANKA LOG BLOG. You have found BIANKA's Blog Log site. BIANKA is the world's first electric powered Nonsuch. Check in to see what new "adventures" Mike and BIANKA have been on lately and what repairs and projects are going on board. Saturday, June 27, 2009. Going electric: Part 1: The why and how. NOTE FROM CAPT. MIKE. IN THE SPRING OF 2008 I BEGAN THE CONVERSION OF MY 30 FOOT SAILBOAT TO ELECTRIC PROPULSION THE 20 "GOING ELECTRIC" POSTS ARE THE CHRONICLE OF THAT PROJECT:. NEXT GOING ELECTRIC POST.

diybanter.com

Seeking Milling Machine Set-up Advice - DIYbanter

http://www.diybanter.com/metalworking/16651-seeking-milling-machine-set-up-advice.html

If this is your first visit, be sure to check out the FAQ. By clicking the link above. You may have to register. Before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. Raquo; DIYbanter forum. Raquo; Do - it - Yourself. Seeking Milling Machine Set-up Advice. Seeking Milling Machine Set-up Advice. Page 1 of 2. May 2nd 04, 10:27 PM. Seeking Milling Machine Set-up Advice. Some real basic advice. Are 110VAC pl...

rebuznopropio.blogspot.com

Upgraded Auto Engine: how to repair water pumps

http://rebuznopropio.blogspot.com/2013/02/how-to-repair-water-pumps.html

Monday, February 25, 2013. How to repair water pumps. Affordable towing service in Houston National Cheap towing service in Houston has the lowest rates and fastest response time. Damage to the common and ordinary encounter of a water pump, either plain or Jet pump is almost the same. Only a few cases rather requires precision and foresight at the time of its service. Total dead water pump. For the record checks do not just use Testpen because Phasenya be detected only while neutralnya not. And also ...

homeshopmachinist.blogspot.com

Home Shop Machinist: Silent air compressor

http://homeshopmachinist.blogspot.com/2010/12/silent-air-compressor.html

Machining with mini mill, mini lathe and other small power tools and teaching you to work with metal, plastic and to guide in projects. By donating you support this blog and my wishlist. Saturday, December 25, 2010. About a year ago I stumbled upon articles in the internet of how to use a freezer or fridge compressor to produce compressed air silently. The only drawback is low air output volume, but my need is occasional and very little, so this fits for me. So I started disassembling the unit to get the...

gainesvilleindustrialelectric.blogspot.com

Industrial Electric Motors: Motor Overload Protection

http://gainesvilleindustrialelectric.blogspot.com/2008/06/motor-overload-protection.html

Many people plan their motor protection around a fuse or breaker. Fuses and breakers look at short-circuit current that happens after the motor has failed. Their job is to protect the power system from damage due to the level of short-circuit current. When they go, it's already too late for your motor. For motor protection, you should look to the overload relay in your starter. April 8, 2011 at 11:20 PM. Gkon Electricals and Electronics Pvt. Ltd. Copper wire suppliers in India. August 9, 2011 at 11:36 PM.

frederickwilliamson.com

Homemade Lathe

http://www.frederickwilliamson.com/Pages-Main/My-Lathe.htm

Natural Edge Salad Bowls. Ordering and Contact Info. A Gallery of Past Work. White Oak Burl Series. Some Shots of My Lathe. I work on a homemade lathe that I have continually modified over the years. It carries a lot of mass now, to resist vibration and oscillation under out-of-balance turning. Here is a general view of the lathe. The bolt holes along the side attach the metal ways I added last year. Here is a close up of the headstock, showing the. Gallery of Past Work. Gallery of Past Work.

gainesvilleindustrialelectric.blogspot.com

Industrial Electric Motors: Testing Electric Motors

http://gainesvilleindustrialelectric.blogspot.com/2008/07/testing-electric-motors.html

Testing electric motors in the field really only requires two meters - an ohmeter and a megohmeter. To test the windings, use an ohmeter. Make sure any jumpers for voltage selection remain connected. For a nine lead, dual voltage motor connected for 480 volts, these would typically be the 4-7, 5-8, and 6-9 connections. Measure the resistance from 1-2, 2-3, and 3-1. The resistance readings should be between 1-2% of each other - in other words, BALANCED! OK, back to the reason we only need to connect the m...

fredwilliamson.com

Homemade Lathe

http://www.fredwilliamson.com/Pages-Main/My-Lathe.htm

Natural Edge Salad Bowls. Ordering and Contact Info. A Gallery of Past Work. White Oak Burl Series. Some Shots of My Lathe. I work on a homemade lathe that I have continually modified over the years. It carries a lot of mass now, to resist vibration and oscillation under out-of-balance turning. Here is a general view of the lathe. The bolt holes along the side attach the metal ways I added last year. Here is a close up of the headstock, showing the. Gallery of Past Work. Gallery of Past Work.

roverpi.blogspot.com

Rover Pi: Controlling two DC motors with Raspberry Pi and the L293D dual H-bridge motor driver

http://roverpi.blogspot.com/2013/07/controlling-two-dc-motors-with.html

Monday, July 15, 2013. Controlling two DC motors with Raspberry Pi and the L293D dual H-bridge motor driver. In order to move our Raspberry Pi powered rover, we will need at least two DC motors to power a left and right set of wheels. The motors will be used to move the rover forward and reverse, as well as rotate left and right. To accomplish this, we figured out how to modify the DC motor tutorial on adafruit.com. Let's first look at the L293D dual H-bridge motor driver and GPIO wiring:. I place the L2...