forum.emittechnologies.com
AFRC Overview – Welcome to the Community and Technical Forum
http://forum.emittechnologies.com/knowledgebase/articles/940221-afrc-overview
Larr; Controls- AFRC. This article was helpful. Flag this article as inaccurate. Flag this article as inaccurate. New and returning users may sign in. Or sign in with. I agree to the terms of service. AFRC Controlling the Engine. Run Signal Trigger and System Temperature Units. Feedback and Knowledge Base. EMIT Technologies, Inc. Your password has been reset. Due to a security incident. We have reset your password. We've just sent you an email to.
forum.emittechnologies.com
Software Update - Controls – Welcome to the Community and Technical Forum
http://forum.emittechnologies.com/knowledgebase/articles/911076-software-update-controls
Software Update - Controls. How to Update Software on the Air Fuel Ratio Controller (AFRC), Governor, Emissions Management Device (EMD), or Annunciator. This article outlines the method for updating the software on an EMIT Air Fuel Ratio Controller (AFRC), Governor, Emissions Management Device (EMD), or Annunciator. The process is the same for all four modules. Insert a blank USB thumb drive into your computer. The thumb drive must be empty and formatted in FAT32 format. Do not change the name of the file.
forum.emittechnologies.com
EMIT Class – Welcome to the Community and Technical Forum
http://forum.emittechnologies.com/forums/347289-forum/suggestions/15308832-emit-class
Send us your question.share an idea here. I see other referencing an EMIT class. Where can I find more information regarding any EMIT training available? Or sign in with. I agree to the terms of service. We’ll send you updates on this idea. Shared this idea ·. July 21, 2016. Flag idea as inappropriate. Flag idea as inappropriate. Or sign in with. I agree to the terms of service. Tech Advisor, EMIT Technologies, Inc. July 22, 2016 17:03. For more information on the classes and scheduling. Or sign in with.
forum.emittechnologies.com
AFRC Installation Guide – Welcome to the Community and Technical Forum
http://forum.emittechnologies.com/knowledgebase/articles/941976-afrc-installation-guide
Larr; Controls- AFRC. The installation guide can be downloaded here: https:/ drive.google.com/open? The quick start guide can be downloaded here: https:/ drive.google.com/open? This article was helpful. Flag this article as inaccurate. Flag this article as inaccurate. New and returning users may sign in. Or sign in with. I agree to the terms of service. AFRC Controlling the Engine. Run Signal Trigger and System Temperature Units. Feedback and Knowledge Base. EMIT Technologies, Inc.
forum.emittechnologies.com
Annunciator Main User Interface Overview – Welcome to the Community and Technical Forum
http://forum.emittechnologies.com/knowledgebase/articles/941526-annunciator-main-user-interface-overview
Annunciator Main User Interface Overview. Larr; Controls- Annunciator. The annunciator has two normal sources of user input- the EIM display and the panel switches. The general operating states and how the panel switches affect the state are as follows. Pressing the panel STOP button will always cause the annunciator to go to the "Stopped" state. If autostart is not used then holding the START button will run the starter, if the annunciator is in a run state. The right side of the annunciator home screen...
forum.emittechnologies.com
Annunciator Setup- Shutdown – Welcome to the Community and Technical Forum
http://forum.emittechnologies.com/knowledgebase/articles/941685-annunciator-setup-shutdown
Larr; Controls- Annunciator. The Shutdown Setup (Pg. 673) can be accessed from the main annunciator setup by selecting Outputs Setup followed by Shutdown Pins . On this page, the type of fuel valve and ignition can be selected to show a diagram for how to wire to the shutdown pins block of the annunciator (Pins 7-10). Note that this does not actually change the functionality of the pins, it only is for viewing the correct wiring. This article was helpful. Flag this article as inaccurate. Or sign in with.
forum.emittechnologies.com
EA Housing – Welcome to the Community and Technical Forum
http://forum.emittechnologies.com/forums/347289-forum/suggestions/15330981-ea-housing
Send us your question.share an idea here. The EA housing has the capacity for 2 catalyst elements. In the situation where only one is needed why is it recommended to place in the space furthest from the inlet? Or sign in with. I agree to the terms of service. We’ll send you updates on this idea. Shared this idea ·. Jul 22, 2016. Flag idea as inappropriate. Flag idea as inappropriate. Or sign in with. I agree to the terms of service. Tech Advisor, EMIT Technologies, Inc. July 22, 2016 5:28 PM.
forum.emittechnologies.com
Knowledge Base – Welcome to the Community and Technical Forum
http://forum.emittechnologies.com/knowledgebase
Larr; Welcome to the Community and Technical Forum. Software Update - Controls. Controls- AFRC →. AFRC Controlling the Engine. 8 articles →. Controls- Annunciator →. Annunciator Main User Interface Overview. Annunciator Basic Setup and Configuration Overview. 23 articles →. Controls- EIM →. EIM Engine Info Page. 11 articles →. Controls- Governor →. Governor Sensor Status Screen. 9 articles →. Controls- Ignition →. 11 articles →. Controls- Panel →. Exhaust- Element Placement Order in EMIT housings.
forum.emittechnologies.com
Annunciator Overview – Welcome to the Community and Technical Forum
http://forum.emittechnologies.com/knowledgebase/articles/941520-annunciator-overview
Larr; Controls- Annunciator. Video available for this topic: https:/ www.youtube.com/watch? All setup and status information is available through the EMIT Interface Module (EIM), an 8 high-brightness touchscreen display. This same display can be used for interfacing with other ETS modules, such as the Air Fuel Ratio Controller (AFRC) or ignition. The annunciator can work in tandem with other ETS modules, if present, in various scenarios, or can act as a standalone annunciator. Thermocouples: Can be confi...