thetazzbot.com
featured | thetazzbot's home on the web
http://www.thetazzbot.com/tag/featured
Thetazzbot's home on the web. Designing for 3D Printing – Making useful things – Part 1. June 13, 2015. I’m starting a series of articles and accompanying videos on designing for 3D printing, using 123D Design as a starting point. As I learn more about other software such as Solidworks, I’ll try to pass that info along. Disclaimer: I’m not an expert, I just figure things out and make notes here on my blog. If those notes help you that’s great! Yep, a simple nut, but this nut is for aluminum extrusion!
thetazzbot.com
Craft Cutting | thetazzbot's home on the web
http://www.thetazzbot.com/category/craft-cutting
Thetazzbot's home on the web. Category Archives: Craft Cutting. Low cost markers that fit the Expression. February 21, 2015. I found some inexpensive markers that fit (a bit tightly) the pen holder in the Cricut Expression. Repurposing the cricut expression. February 19, 2015. Now that I have the firmware in a working condition, I’m contemplating all the neat little uses I can get out of this machine. Luckily, I don’t have a huge investment in cartridges like this person on Craigslist:. I mean, really!
thetazzbot.com
3D Printed Terminator Skull T-800 | thetazzbot's home on the web
http://www.thetazzbot.com/2015/06/09/3d-printed-terminator-skull-t-800
Thetazzbot's home on the web. 3D Printed Terminator Skull T-800. June 9, 2015. Blue – PET Filament from Made Solid. I think this was printed too fast or needed more extrusion. The camera shows like it is pitted but when you hold it in your hand you really don’t see that but it does have a texture that indicates it. This was printed first, and skipped right at the line by the upper teeth. The detail was very nice though. ABS. 3D Printing Fusible Alloys. Leave a Reply Cancel reply. You must be logged in.
thetazzbot.com
Analysis of the Y Axis (Bed) on a Cartesian style printer | thetazzbot's home on the web
http://www.thetazzbot.com/2015/06/03/analysis-of-the-y-axis-bed-on-a-cartesian-style-printer
Thetazzbot's home on the web. Analysis of the Y Axis (Bed) on a Cartesian style printer. June 3, 2015. For beds arranged like this, the situation is different and maybe non-existent:. Three bearing designs are great for machines that have expensive, tight tolerance components. For RepRap printers, four bearings are probably better over all. The following approach would minimize the problem for three bearing designs:. Hardening your Prusa i3 3D printer. Finally getting some decent prints. To post a comment.
thetazzbot.com
RepRap 3D printer project is not for the faint at heart | thetazzbot's home on the web
http://www.thetazzbot.com/2015/04/08/reprap-3d-printer-project-is-not-for-the-faint-at-heart
Thetazzbot's home on the web. RepRap 3D printer project is not for the faint at heart. April 8, 2015. So I launched my “RepRap” 3D printer project a few weeks ago. I am building the Prusa i3 printer using 6mm acryllic for the front and side support wings. A picture of it is shown below:. 8220;RepRap” printer designs available for the do it yourselfer. The concept is theoretically good: Build a bare bones printer, then use it to build the parts for a better printer. The original design, aka Prusa Mendel.
thetazzbot.com
3D Printers | thetazzbot's home on the web
http://www.thetazzbot.com/category/3d-printers
Thetazzbot's home on the web. Category Archives: 3D Printers. Designing for 3D Printing – Making useful things – Part 1. June 13, 2015. I’m starting a series of articles and accompanying videos on designing for 3D printing, using 123D Design as a starting point. As I learn more about other software such as Solidworks, I’ll try to pass that info along. Disclaimer: I’m not an expert, I just figure things out and make notes here on my blog. If those notes help you that’s great! It’s difficult to know ...
thetazzbot.com
Electronics | thetazzbot's home on the web
http://www.thetazzbot.com/category/electronics
Thetazzbot's home on the web. Magic Sing Karaoke Microphone Tear Down. January 11, 2016. I bought this Magic Sing Karaoke microphone system many years ago and my family and friends have enjoyed and some times been annoyed by it quite often! It truly is a really neat gadget. I’ve got a plethora of photos of the inside, the outside and the on screen displays. The microphone base has 2500 songs built in, and has several add on slots for song chips that are available online for about $60 a pop. The chip on t...
thetazzbot.com
Reverse Engineering | thetazzbot's home on the web
http://www.thetazzbot.com/category/reverse-engineering
Thetazzbot's home on the web. Category Archives: Reverse Engineering. Magic Sing Karaoke Microphone Tear Down. January 11, 2016. I bought this Magic Sing Karaoke microphone system many years ago and my family and friends have enjoyed and some times been annoyed by it quite often! It truly is a really neat gadget. I’ve got a plethora of photos of the inside, the outside and the on screen displays. The system includes two cordless microphones that also each act as a remote control. Let’s open it up! The ch...
thetazzbot.com
3D Printing Aria the Dragon | thetazzbot's home on the web
http://www.thetazzbot.com/2015/05/24/3d-printing-aria-the-dragon
Thetazzbot's home on the web. 3D Printing Aria the Dragon. May 24, 2015. My most challenging print so far. Up to now I’ve been printing parts for additional printers. Thought I would tackle something majestic. I love dragons. Here is Aria The Dragon. But So far she doesn’t look that great. I’m trying to figure out the right settings for her. I’d like to print at .1 or .2 mm layer height. The above was printed with Repetier Host using Cura slicing. Rectangular infill, 50% speed, .3mm layer. No raft or brim.
