FREEPTPTN.COM

miorzaini.blogspot.com

Engineering Boy: Flush Floor Trunking: The Wrong Things That Most People Do!

http://miorzaini.blogspot.com/2014/02/flush-floor-trunking-wrong-things-that.html

Lets talk about engineering. Feb 6, 2014. Flush Floor Trunking: The Wrong Things That Most People Do! This is the things that engineers and site workers must avoid when installing flush floor trunking (FFT); cable congested in FFT. FFT normally consist of single, 2 compartments and 3 compartments of internal trunking. These compartments are segregated between each other and each compartment shall not be shared together. Labels: Flush Floor Trunking. Subscribe to: Post Comments (Atom). Lesson learnt on ar...

miorzaini.blogspot.com

Engineering Boy: What Is Skin Effect?

http://miorzaini.blogspot.com/2014/09/what-is-skin-effect.html

Lets talk about engineering. Sep 22, 2014. What Is Skin Effect? Skin effect is a condition where A.C (alternating Current) tents to travel on the surface of the conductor, as frequency increases. It is easy to explain by comparing the resistance between these 3 scenarios DC Resistance, AC Resistance in Low-frequency and AC Resistance in High-frequency. Photo Credit to www.allaboutcircuits.com/. Labels: high frequency current. What is skin effect. Subscribe to: Post Comments (Atom). Types Of Earthing Syst...

miorzaini.blogspot.com

Engineering Boy: How To Calculate The Power Factor Correction

http://miorzaini.blogspot.com/2010/10/how-to-calculate-power-factor.html

Lets talk about engineering. Oct 9, 2010. How To Calculate The Power Factor Correction. Let says, there is a small Multipurpose Hall with the total loads as per tabulated below and you are be ing assigned to design the power factor correction. Before designing the power factor correction, you should know what’s the purpose in correcting the power factor and how to do the correction of power factor? Bear in mind that pumps and motors are the inductive loads. In order to obtain an efficient systems;. The u...

miorzaini.blogspot.com

Engineering Boy: Inspection Checklist Form

http://miorzaini.blogspot.com/2010/11/inspection-checklist-form.html

Lets talk about engineering. Nov 5, 2010. After all the hard works in designing the electrical systems done by the Consultant; now, it is the time for electrical contractor to implement that design. The question is.how to check that all the works carried out by the contractor are in properly manner and according to the drawing? Below are few samples of inspection checklist than can be used as guidance for you! For a sample of inspection checklist. 1 Opening and Penetration Inspection Checklist. 16 Small ...

miorzaini.blogspot.com

Engineering Boy: Technical Term

http://miorzaini.blogspot.com/p/technical-term.html

Lets talk about engineering. Below are the Technical Term that commonly used in electrical telecommuniation. A term denoting a 10-pair disconnection type of copper cable terminatiion fixture. The 110 block support Cat-5e type levels og signalling and is used within the BMDF, SDF, MC and PABX rack panel mount facilities in this specification. A term denoting communication cabinet that supports both passive and active electronics components. The cabinet is typically one or two rail rack with an enclosu...

miorzaini.blogspot.com

Engineering Boy: How To Calculate The Voltage Drop?

http://miorzaini.blogspot.com/2010/10/how-to-calculate-voltage-drop.html

Lets talk about engineering. Oct 11, 2010. How To Calculate The Voltage Drop? What is Voltage Drop? The term “Voltage Drop”. Is essentially refer to the reduction. Between the source of power to the end load where the source of power supply to. How This Voltage Drop Happen? By law of nature; Energy cannot be created and it also cannot be demolish. However, energy can be transform from one form of energy to another form of energy (ie: solar energy transform to electricity). L = Distance of cable (in Metre).

miorzaini.blogspot.com

Engineering Boy: How To Eliminate Harmonic In Electrical System?

http://miorzaini.blogspot.com/2013/11/how-to-eliminate-harmonic-in-electrical.html

Lets talk about engineering. Nov 20, 2013. How To Eliminate Harmonic In Electrical System? What Is Harmonics in Electrical System? Harmonic define as any Non-Linear Current or Voltage in an electrical distribution system. The presence of harmonics in electrical systems means that current and voltage are distorted and deviate from sinusoidal waveforms. Harmonic shouldn’t be thought of as an acoustic or vibration harmonic, but simply any electrical device that draws current unpropotionally to voltage.

searizeel.blogspot.com

OC: PTPTN Loan Repayment

http://searizeel.blogspot.com/2013/05/ptptn-loan-repayment.html

Thursday, May 09, 2013. It's actually easier than I thought. Gosh, to think that I was planning to visit. The HQ just to enquire about paying the loan when that service is already. Provided at your account. Here, I'll walk you through if you're somewhat. Like me before this. And if you already know your loan ID, you may follow this one. If you don't, then just do this:. Go to PTPN home. I donno why the icon isn't loading. Anyways, just click the one next to e-sspsn-i. And you should be at the login page.

miorzaini.blogspot.com

Engineering Boy: What Is Ultimate Breaking Capacity (Icu) & Service Breaking Capacity (Ics)

http://miorzaini.blogspot.com/2013/10/what-is-ultimate-breaking-capacity-icu.html

Lets talk about engineering. Oct 17, 2013. What Is Ultimate Breaking Capacity (Icu) and Service Breaking Capacity (Ics). To all engineers…you must know what MCCB is! But have you notice the Icu and Ics percentage indicate at the MCCB? For example; the above MCCB shows that the Ics = 50% Icu. Those values are actually the breaking capacity of the circuit breaker namely as per below;. Icu: Rated Ultimate Short-circuit breaking capacity (in kA). Ics: Rated Service Short-circuit breaking capacity (in kA).