g9toengineering.com
Electromyography Controlled Car
http://www.g9toengineering.com/MechatronicsStudio/Electromygraphy.htm
Khan, and Kyla Sun, Department of Mechanical Engineering, University of Ottawa. The sensor is a fabric coated with a 0.5% saline based conductive gel and AgAgCl. They are 10-mm in height and 1.25 by 0.875 in length and width. The sensors are snap-on style to avoid constant wire tempering within the circuit; thus the input wires are not constantly being changed. The design features for the IN118 are:. The bandwidth can be as wide as 70kHz at a high gain of 100 due to the current-feedback input circuitry.
g9toengineering.com
Mo The Robot
http://www.g9toengineering.com/MechatronicsStudio/MoTheRobot.htm
Chris Falconi, Jon Gilchrist, Ryan Jordan, Mechanical Engineering, University of Ottawa. 2 High-Torque Brushed DC Motors. Multiple Solder-On Circuit Boards. Batteries: 2x 9V, 1x 7.2V, 1x 6V. Multiple Toggle and Momentary Switches. PING Ultrasonic Proximity Sensor. 3 Infrared Reflectance Sensors. High Strength Epoxy, Super Glue, Acrylic Solvent Cement. Brass and Aluminum Tubing and Rods. Double Sided Foam Tape. Drill and Drill Press. Electronics and Control Systems. As an additional feature, the robot is ...
g9toengineering.com
Activities
http://www.g9toengineering.com/activities/main.htm
Ottawa Engineers in Classroom! Engaging High School and Engineering Students. 12:00-14:30 Wednesday: November 28, 2007. Students from the Faculty of Engineering. All Saints Catholic High School. On Wednesday, November 28, 2007. They made presentations about mechatronic engineering design. Focused on integration of math, science, engineering, and computer technology in engineering design. Ottawa Engineers in Classroom! 12:00-13:00 Monday: March 31, 2008. Students from the Faculty of Engineering.
g9toengineering.com
Following Flames IR Robot
http://www.g9toengineering.com/MechatronicsStudio/FollowingFlames.htm
Following Flames IR Robot. Darik Oreskovich, Department of Mechanical Engineering, University of Ottawa. 1 Sharp IR Sensor. 1 Light Dependent Resistor. 1 1602 LCD Display. Various Fasteners, Nuts, Washers, and Bolts. 2 Rubber Wheels and 1 Castor Wheel. Soldering Iron, Solder, and Flux. A driver board is used in order to regulate the voltage given to each motor and to prevent over-loading or over-heating. When the light levels in the room are too low, the robot will stop its searching or following and a b...
g9toengineering.com
Off Road Electric Vehicle
http://www.g9toengineering.com/MechatronicsStudio/Offroadvehicle.htm
Off Road Electric Vehicle. Brad Gordon, Jake Richardson, Department of Mechanical Engineering, University of Ottawa. Why we built it? Figure 1: Example of Rack and Pinion Steering. The suspension we used consists of a solid beam shock suspension in the front and leaf spring in the back. This allows the vehicle to spring over off-road terrain and maintain a rigid stance. The EV has two drum brakes built into the ends of the differential. Both these brakes are connected to the rear wheels and are engag...
g9toengineering.com
Engineering
http://www.g9toengineering.com/engineering/main.htm
Derived from the Latin ingenium, engineering. Means something like brilliant idea, flash of genius. The word was created in the 16th century and originally described a profession. That we would probably call an artistic inventor. Combines applied mathematical, scientific, and technical principles,. To yield tangible end products which can be made, produced, and constructed. Differs from science in that it must take requirements into account including. A World without Engineers! Specialists, and many more!
g9toengineering.com
Mechatronics Learning Studio
http://www.g9toengineering.com/MechatronicsStudio/main.htm
Mechatronics Learning Studio: Archive. The Electromagnetic Solenoid Cannon. Crime Fighting Coil Gun. Hand to Mechanical Hand. Pelton Wheel Drive MicroHydro Plant. Simple Wind Turbine System. Omni-directional Guided Robotic Entity. Myoelectric Controlled Prosthesis Hand. Control System and Feedback.
g9toengineering.com
Barbot
http://www.g9toengineering.com/MechatronicsStudio/Barbot.htm
Andre Maurice, Terrence Phenix, Jory Seguin, Department of Mechanical Engineering, University of Ottawa.
g9toengineering.com
Quadcopter
http://www.g9toengineering.com/MechatronicsStudio/Quadcopter.htm
Kiel Graham, Josh Kramer and Eric Sabourin, Department of Mechanical Engineering, University of Ottawa. The Transmitter and receiver used had the following specifications: a 2.4 GHz 4 channel transmitter with a 6 channel receiver. The rudder channel controls the yaw of the quad copter (left), and the elevators channel controls the pitch of the quad copter (right). The frame was constructed mainly out of aluminum. 6061 Aluminum has a mass of 2.7 g/cm3. The mechanical properties are desired fro...The weigh...
ariselab.ca
Laboratoire d'innovations ARISE
http://www.ariselab.ca/fr
Bienvenue au Laboratoire d'innovations ARISE, un club où les étudiants et étudiantes d'uOttawa menent de la recherche et dévelopement en mécatronique, robotique et ingénierie électrique. Nous avons deux groupes principaux dans ARISE :. Nous aimerions remercier les organismes suivants pour leur appui continu pour notre laboratoire, le club et nos projets. Pour plus d'informations, veuillez contacter info@ariselab.ca. Standards Web : XHTML.
