alternativecomponents.com
Alternative Components home page
http://www.alternativecomponents.com/index.html
Quality Fabricated Tube and Wire Products. Some of the fabricated tube products made at Alternative Components are shown below. many of the parts are automotive, such as the seat frame, fuel fill tube and Prowler luggage rack. Many others are non automotive such as the gas furnace burner, and the gas mask water tube. AC Friends and Associates. Ind Servo Hydraulics, Inc. A growing array of headers are available at Alternative Components for hot rods and late model cars.
alternativecomponents.com
bendertools
http://www.alternativecomponents.com/bendertools.htm
Alternative Components now offers standard Eaton Leonard tube bender master collets and inserts. These collets are for Eaton Leonard horizontal rotary draw benders. The master collet has a 3 tube diameter capacity. Using collet inserts, any tube size less than 3 diameter can be held. Special configurations can be made such as inserts to hold square or shaped tube. Specials will be quoted on request. Master Collet and Shallow (Short) Inserts. Master Collet and Extended Inserts. AC Friends and Associates.
alternativecomponents.com
Wireform
http://www.alternativecomponents.com/wireform.htm
Wire Fabricating at Alternative Components includes but is not limited to bending, upsetting, flattening and machining. Gear shift lever for ATV. Wire Forms, one with an upset. Symmetrical cold formed flat. AC Friends and Associates. Ind Servo Hydraulics, Inc. A growing array of headers are available at Alternative Components for hot rods and late model cars.
alternativecomponents.com
Engineering
http://www.alternativecomponents.com/engineering.htm
Tool design and assembly are done in house to conserve time and cost and increase quality. Below are parts from just a few of the programs that Engineering has supported. Formed end of Radiator Support. Mid section of Radiator Support. IP panel mount with push nuts. Configurations of Gas Tank Spuds. AC Friends and Associates. Ind Servo Hydraulics, Inc. A growing array of headers are available at Alternative Components for hot rods and late model cars.
alternativecomponents.com
Prototype
http://www.alternativecomponents.com/prototype.htm
Prototyping is an essential service that is provided by Alternative Components for short run quantities or to confirm part fit and function before committing to production tools. The prototype service also researches and develops new fabricating processes that are required to produce new product. Shown below are just a few examples of the prototypes that Alternative Components is capable of. Alternative Components welcomes inquiries about capabilities. Please contact. Integral wire lug for a ground wire.
alternativecomponents.com
Railings
http://www.alternativecomponents.com/railing.htm
These railings are made of 304 brushed stainless steel. The vertical tubes are 1.5" diameter with 5/8" rails. All intersecting joints are welded. Lower stairs from the great room. Cat walk above the great room with stainless steel railing on both sides. Upper stairs from the landing. Lower stairs from the landing. These railings are powder coated steel with 5/8" square rails and 1 1/2" X 2" uprights. The top rails are 1" X 3". All intersecting joints are welded. Architectural railing at restaurant corner.
alternativecomponents.com
New Equipment
http://www.alternativecomponents.com/newequip.htm
M3000 Triple Action End Former. This new end former is capable of beading 2.5 diameter low carbon steel tube with .083 wall. Just a few of the M3000. Features and capabilities are listed below:. Safety clamps close at low pressure Max. system pressure of 3000 psi. Automatic 1, 2, or 3 punch hits Custom cycle sequences. Clamp wedges to prevent clamp breathing Punch shuttle shot pins to ensure punch centering. Slide plate to accommodate extra long punches Tie rod construction for punch - clamp alignment.
alternativecomponents.com
Headers
http://www.alternativecomponents.com/headers.htm
Most exhaust products at Alternative Components are made of 304L stainless steel. Other materials are available for fabricating headers such as 409 stainless steel or low carbon steel. The collectors and tubes are designed and fabricated in house. Intermediate pipes and other exhaust components are also available at Alternative Components. AC Friends and Associates. Ind Servo Hydraulics, Inc. A growing array of headers are available at Alternative Components for hot rods and late model cars.
alternativecomponents.com
Quality
http://www.alternativecomponents.com/quality.htm
Alternative Components is committed to meeting customer satisfaction through on time delivery, quality products, innovation and continuous improvement. AC Friends and Associates. Ind Servo Hydraulics, Inc. A growing array of headers are available at Alternative Components for hot rods and late model cars.
alternativecomponents.com
About Us
http://www.alternativecomponents.com/aboutus.htm
Introduction to our organization. Alternative Components, LLC., was founded August 1996. The company is privately held and does business in Warren, Michigan. Annual sales are currently over 4 million dollars. We are located next to the new Daimler Chrysler Technology Center (2700 East 9 Mile, Warren, MI) and have a facility size of 25,600 sq. ft. AC Friends and Associates. Ind Servo Hydraulics, Inc. A growing array of headers are available at Alternative Components for hot rods and late model cars.
