pocketshear.com
PSH06-O Parts Order
http://www.pocketshear.com/Forms/601PartsOrder.htm
Parts Order Submission Form - Model PSH06-O. Job Site or Ship to Address:. Side Frame - Main Housing. Requires Old Serial Number). Side Frame - Cover. Back-Up / Wear Plate. Piston w/o holes (inner). 6 Standard Nose Piece. 6 Standard Rotating Shear Blade. 6 Fixed Shear Blade. Clamp Rear Cover Plate. Clamp Spring - Green. Bolt Kit, Complete. Choose Shipping Method Required. UPS Second Day Air. UPS Third Day Air.
pocketshear.com
PSH05-O Parts Order
http://www.pocketshear.com/Forms/501PartsOrder.htm
Parts Order Submission Form - Model PSH05-O. Job Site or Ship to Address:. Side Frame - Main Housing. Requires Old Serial Number). Side Frame - Cover. Back-Up / Wear Plate. Piston w/o holes (inner). 5 Standard Nose Piece. 5 Standard Rotating Shear Blade. 5 Fixed Shear Blade. Clamp Rear Cover Plate. Clamp Spring - Green. Bolt Kit, Complete. Choose Shipping Method Required. UPS Second Day Air. UPS Third Day Air.
pocketshear.com
PocketSHEAR®
http://www.pocketshear.com/Content/PocketShearabout.htm
The PocketSHEAR from PRECISION-HAYES. The only solution for flameless tendon shearing. The PocketSHEAR is a patented, cold shear, that slips over the strand at the end of the pocket and slides into the pocket up to the anchor. It is then hydraulically actuated to cold-shear the strand approximately 1" from the face of the anchor. In high corrosion environments, a 2" pocketformer is commonly used and the PocketSHEAR will then provide 1" concrete cover over the end of the Tendon.
pocketshear.com
PocketSHEAR® Construction Specifications
http://www.pocketshear.com/Content/PocketShearConstSpecs.htm
The PocketSHEAR from PRECISION-HAYES. Standard Specification for cutting PC Strand Tendons after recording elongations. Cutting Tendons After Stressing:. Do not cut tendons or cover pockets until elongation records are reviewed and accepted by the Engineer of Record or Architect. Clean tendons, anchorages and pockets of corrosion preventitive coating with non-corrosive solvent before removal of excess length of post-tensioning tendons. All tendon ends shall be left clean and free of burrs.
pocketshear.com
PocketSHEAR® Technical Information
http://www.pocketshear.com/Content/PocketShearTechInfo.htm
The PocketSHEAR from PRECISION-HAYES. PocketSHEAR Models PSH05-O and PSH06-O. 1/2" P C Strand. 6" P C Strand. ASTM A416, sheathing stripped back. Does not include weight of hoses, etc. 2,000 to 2,700 psi. 2,700 to 3,000 psi. Varies with strand hardness. 2,000 to 2,500 cuts. 2,000 to 2,500 cuts. Varies with strand hardness. Cut Cycle Time, Manual. Varies with stressing gear pump model and condition. Cut Cycle Time, Auto.
promos.enerpac.com
Precision-Hayes.com
http://promos.enerpac.com/precision-hayes.com
Precision-Hayes International is a merger of Hayes Industries and Precision SURE-LOCK.
pocketshear.com
PocketSHEAR® FAQ
http://www.pocketshear.com/Content/PocketShearFAQ.htm
The PocketSHEAR from PRECISION-HAYES. What is a PocketSHEAR? A PocketSHEAR is a "Specific-Use" device solely intended for cold-shearing PC Strand Tendons within the pocket after stressing operations are complete and approved. How was it developed? Why do I need one? How does it work? The PocketSHEAR is a hydraulic device designed with two cutting blades that act in a rotating fashion in order to cold-shear the PC Strand Tendon at a certain dimension within the pocket. The PocketSHEAR does not push, p...
pocketshear.com
PocketSHEAR® Jobsites
http://www.pocketshear.com/jobsites.htm
The PocketSHEAR from PRECISION-HAYES. The ZUPS-0208SB Pump is specifically developed to run the PocketShear at optimum flow and pressure, allowing the tool to stall before damage can occur. The PSH05-O PocketShear, with its narrow nose, fits even in congested areas, like this beam interface. The unique tendon clamp assures proper location of the tendon in the tool and also holds the tendon tail after cutting, preventing it from falling to the work area below.
