colaser.org
Sol Diego Laser @ Colab
http://colaser.org/2015/02/04/engraving-slate-with-a-jig/img_4433
Sol Diego Laser @ Colab. Laser cutting/engraving for the Sol Diego community. Skip to primary content. February 4, 2015. At 3264 × 2448. In Engraving Slate (with a jig). Second raster test, still at full power but with reduced speed. The cut is perhaps too deep now. Leave a Reply Cancel reply. Your email address will not be published. Required fields are marked *. Proudly powered by WordPress.
colaser.org
February Class Scheduled | Sol Diego Laser @ Colab
http://colaser.org/2015/02/20/february-class-scheduled
Sol Diego Laser @ Colab. Laser cutting/engraving for the Sol Diego community. Skip to primary content. February 20, 2015. Basic laser operation and safety class is scheduled for Tuesday, February 24, at 6:30pm – 10pm. Please email me class@colaser.org. To reserve your place in the class. Because the laser room is small, the class size is limited to 6. This entry was posted in Classes. View all posts by Sol Diego →. 2 thoughts on “ February Class Scheduled. February 22, 2015 at 10:54 pm.
colaser.org
Sol Diego Laser @ Colab
http://colaser.org/2015/02/04/engraving-slate-with-a-jig/img_4431
Sol Diego Laser @ Colab. Laser cutting/engraving for the Sol Diego community. Skip to primary content. February 4, 2015. At 3264 × 2448. In Engraving Slate (with a jig). First raster engraving test. At this power level (full power and full speed), the color changes (with a few spots left black) but the cut is so shallow it’s hard to detect. Leave a Reply Cancel reply. Your email address will not be published. Required fields are marked *. Proudly powered by WordPress.
colaser.org
Sol Diego Laser @ Colab
http://colaser.org/2015/02/04/engraving-slate-with-a-jig/jig
Sol Diego Laser @ Colab. Laser cutting/engraving for the Sol Diego community. Skip to primary content. February 4, 2015. At 1428 × 1202. In Engraving Slate (with a jig). Raster artwork combined with a vector circle to guide material placement. Leave a Reply Cancel reply. Your email address will not be published. Required fields are marked *. Proudly powered by WordPress.
colaser.org
Engraving Slate (with a jig) | Sol Diego Laser @ Colab
http://colaser.org/2015/02/04/engraving-slate-with-a-jig
Sol Diego Laser @ Colab. Laser cutting/engraving for the Sol Diego community. Skip to primary content. Engraving Slate (with a jig). February 4, 2015. I found some slate coasters on the bargain shelf at Jo-Ann the other day, and tried laser engraving them. The results were pretty good! See the photo gallery below. In fairly short order I was able to make a set of four coasters. With the simple jig the engraving is consistently centered so they look good even side-by-side. Here’s the first coaster p...
colaser.org
Sol Diego Laser @ Colab | Laser cutting/engraving for the Sol Diego community | Page 2
http://colaser.org/page/2
Sol Diego Laser @ Colab. Laser cutting/engraving for the Sol Diego community. Skip to primary content. Skip to secondary content. Newer posts →. Class scheduled for Sunday, November 15 at 1pm. November 7, 2015. Another session of the basic operation and safety course has been scheduled for Sunday, November 15, at 1pm. Email class@colaser.org to sign up. October 25, 2015. I’ve been wanting to try engraving a glass mirror. I picked up several 2-inch round mirrors from the craft store for a test. In the vid...
colaser.org
Sol Diego | Sol Diego Laser @ Colab
http://colaser.org/author/sol-pressmaster
Sol Diego Laser @ Colab. Laser cutting/engraving for the Sol Diego community. Skip to primary content. Skip to secondary content. Author Archives: Sol Diego. February 20, 2015. Basic laser operation and safety class is scheduled for Tuesday, February 24, at 6:30pm – 10pm. Please email me class@colaser.org. To reserve your place in the class. Because the laser room is small, the class size is limited to 6. November 22, 2014. On both jobs, you can clearly see the spot where the laser started to cut each ve...
colaser.org
Inkscape 0.91 available now | Sol Diego Laser @ Colab
http://colaser.org/2015/02/01/inkscape-0-91-available-now
Sol Diego Laser @ Colab. Laser cutting/engraving for the Sol Diego community. Skip to primary content. Inkscape 0.91 available now. February 1, 2015. After a long development cycle, the developers of the excellent free vector drawing program Inkscape have just released a major new version, numbered 0.91. There is a good article about the updates available from Libre Graphics World. And you can download the new software (Windows, Mac, or Linux) from Inkscape.org. This entry was posted in Announce.
colaser.org
Sol Diego Laser @ Colab
http://colaser.org/2015/02/04/engraving-slate-with-a-jig/img_4436
Sol Diego Laser @ Colab. Laser cutting/engraving for the Sol Diego community. Skip to primary content. February 4, 2015. At 3264 × 2448. In Engraving Slate (with a jig). After engraving. The white dust is deposited during engraving. You can see that the exhaust air flow is enough to blow the dust toward the rear. Leave a Reply Cancel reply. Your email address will not be published. Required fields are marked *. Proudly powered by WordPress.
colaser.org
Download | Sol Diego Laser @ Colab
http://colaser.org/download
Sol Diego Laser @ Colab. Laser cutting/engraving for the Sol Diego community. Skip to primary content. This PDF document is an attempt to cover every step and procedure you need to follow to use the laser for routine work. If you have taken the class and still feel unsure about all the steps, this document might help. There should always be a copy of this document in the laser room. If in doubt, please ask. Software and operation manual. Z table adjustment guide. Is popular with makers for lasers and oth...
